A Lungvar sernak sehchanthar saknak thilri chuahnak ah a biapi tukmi hmunhma a lak. Concrete block, lam cawhnak lungvar, a ummi lungvar, le pawngkam he aa remmi inn saknak thilri pawl an herh chin lengmang caah, sehzung tam deuh nih mah tein an hman Block Sehs le thilchuah tthatnak tthanchoter awkah lungvar chuahnak lam pawl kha lim.

Sihmanhsehlaw, caan saupi riantuannak ah, lungvar sernak seh hna nih riantuannak ningcang lo, thilri kong, thilri rawhralnak, asiloah zohkhenhnak tlamtling lo ruangah harnak phunphun an tong kho.

A tlangpi in buainak hna cu:

• Lungvar sernak seh nih lungvar a chuah lo;
• Ti tthawnnak a niam;
• Lungvar thazaang a ttha lo;
• Aa tluk lomi lungvar cunglei;
• Mah tein a rawkmi system;
• A hlei in seh hninhnak asiloah aw.

Hi hna hngalhthiamnak a tlangpi in lungvar sernak seh harnak le a phichuak operator pawl kha buaibainak pawl kha rang tein hngalh khawhnak, seh riantuan caan zorternak le thilchuah ttha tein chiah khawhnak ah a bawmh khawh hna.

1. Lungvar sernak seh nih lungvar a chuah kho lo

A langh tawnmi zawtnak hmelchunhnak

Operator pawl nih an chim tawnmi buainak pakhat cu seh cu a ttha tein a kal ko nain a ttha mi lungvar a chuah kho lo.

A tlangpi in zawtnak hmelchunhnak hna cu:

• Mold nih cun lungvar tling a ser lo;
• Lungvar pawl cu an ser hnu ah an i tthen asiloah an i tthen;
• Rawl peknak nih thilri a za tawk a pek khawh lo;
• Thilchuah khawhnak tthatnak cu ruahlo piin a zor.

A ruang a si khomi

A ruang zeimawzat a um kho:

1. A dik lomi thilri cawhmi

Lungvar tthatnak cu thilri hmanmi zat cungah tampi aa hngat. Cement, thetse, lungvar, vutcam, asiloah thilri dangdang hna kha ṭha tein cawh lo ahcun, seh nih a fekmi lungvar a chuah khawh lo men lai.

2. Rawl Peknak System Buainak

Thilri peknak system cu a phih asiloah rawl peknak rangnak a dik lo ahcun, mold nih thilri a za tawk a hmuh men lai lo.

3. Mold Buainak

A rawkmi asiloah a thurhnawmmi hling nih lungvar muisam le chuah khawhnak a dikthliar in a hnorsuan khawh.

A phichuak

Hi buainak tawlrel awkah:

• Thilri hmanmi phunglam kha zohfel law remh;
• Rawl peknak system kha zungzal in thianh;
• Mold dirhmun kha zohfel;
• Rawl pek caan le hninhnak parameter pawl kha remh.

Thilri timhtuahnak ttha le ttha tein zohfelnak nih lungvar sernak seh sernak ah harnak tampi a kham khawh.

2. Hydraulic Brick Machine cu a tlawmmi hneknak a ngei

Hydraulic system cu chanthar lungvar sernak seh ah a biapi bikmi pakhat a si. A tlawm tukmi hneknak nih lungvar a tlawm le a fek kha direct in a hnorsuan khawh.

A langh tawnmi zawtnak hmelchunhnak

• Lungvar cu fawi tein a kuai;
• Lungvar thazaang nih a herhmi a tlinh lo;
• Seh hmehnak kalning cu a fek lo;
• Hydraulic cylinder cu tlawmpal in aa chawk.

A ruang a si khomi

Hydraulic Chiti A niam

Hydraulic oil a tlawm ahcun system pressure a zorter khawh i seh riantuan ning a hnorsuan khawh.

Hydraulic Oil thurhnawmhnak

A thurhnawmmi hydraulic chiti nih pump, valve le a dang thilri pawl a hrawh khawh.

Hydraulic Pump A Rawhnak

A rawkmi hydraulic pump nih lungvar sernak caah a za tawk in thazaang a pek kho lo.

Seal Wear

A hlun cangmi hydraulic kharnak nih chiti a chuahter khawh i thazaang a zorter khawh.

Buainak tawlrelnak lam

Operator pawl nih:

• Hydraulic chiti dat kha ttha tein zohfel;
• Zohkhenhnak caan suaimi ningin hydraulic chiti kha thlen;
• Hydraulic pipe le pehtlaihnak pawl kha zohfel hna;
• A rawkmi seal le thilri pawl kha thlen hna.

Riantuan ning tthatnak caah hydraulic system zohkhenh zungzal cu a biapi tukmi a si ti in lungvar sernak seh.

3. Chuah hnu ah lungvar tthatnak a ttha lo

Seh cu a ttha tein rian a ttuan ko zongah, a ttha lomi lungvar a chuak kho rih.

A tlangpi in harnak

• Lungtum cungah tthencheunak a lang;
• Lungvar cunglei cu aa tluk lo;
• Lungvar tthen pawl cu an rawk;
• Lungvar thazaang cu a za lo.

A ruang bik

Thilri tthatnak

A ttha lomi thilri asiloah a dik lomi zat nih a donghnak thilri thazaang a zorter khawh.

A dik lomi hneknak thlennak

Molding pressure a niam tuk ahcun, lungvar cu a tlawm tuk men lai lo.

A dik lomi thlopnak lam

Molding tuah hnu ah, lungvar pawl nih a herhmi thazaang hmuh khawhnak dingah a ttha tein a fekmi caan le thil sining a herh.

A phichuak

Thil sertu le riantuantu hna nih:

• Thilri hmanmi zat kha ttha tein ser;
• Molding pressure kha dik tein remh;
• Damhnak lam hna kha tthanchoter;
• Seh hninhnak le sernak parameters kha zoh.

Thil sernak kalning dihlak a dikthliar in hman cu a biapi, seh lawng si loin.

4. Mah tein a cawlcangmi lungvar sernak seh riantuannak ah harnak

Chanthar sehzung tampi nih amah tein lungvar sernak seh le riantuantu man tlawmternak le thilchuak karhternak caah amah tein a cawlcangmi lungvar chuahnak lam hna.

Sihmanhsehlaw, mah tein rian a ttuanmi hna nih a caan ah harnak an tong men lai.

A tlangpi in buainak

• Seh cu ruahlo piin a dir;
• Ralrinnak hmelchunhnak a lang;
• Sensor pawl nih an leh lo;
• Thilchuahnak line riantuannak cu a fek lo.

A ruang a si khomi

• Electric system buainak;
• Sensor a tlamtlin lonak;
• PLC uknak palhnak;
• A tthawng lomi hri pehtlaihnak.

A rannak in zohfelnak

Operator pawl nih an zoh awk a si:

• Control cabinet dirhmun;
• Sensor dirhmun;
• Electric pehtlaihnak;
• PLC program riantuannak.

Electric thilri pawl kha ttha tein zohfelnak nih ruahlopi in thilchuahnak a kham khawh.

5. Lungvar sernak seh nih aw tam tuk a chuahter

A ttha lomi aw cu a tlangpi in thilri cheukhat zohfel a herh ti ralrin peknak hmelchunhnak a si.

A ruang tlangpi

• A tthawng lomi seh thilri hna;
• Hriamnam tlawm;
• Motor bearing a rawkmi;
• Hydraulic system buainak.

A phichuak

Ruahchannak pekmi tuahsernak:

• A tthawng lomi hri le thilri pawl kha hren hna;
• A ttha mi hriak chap;
• Motor bearings zoh;
• Hydraulic thilri pawl kha zohfel hna.

Caan saupi chung aa dangmi aw-an kha zeirel loin umnak nih thilri rawhnak ngan deuh le remhnak man sang deuh a chuahter khawh.

6. Zeitindah Lungvar Sernak Seh Zohkhenh Lai le A Rawhnak Tlawmter Lai?

A zungzal in zohkhenhnak cu seh nunnak sauternak le remh a tlawmternak lam tha bik pakhat a si.

Nifatin Zohkhenhnak

Operator pawl nih:

• Chuah dih hnu ah mold pawl kha thianh hna;
• A tangmi thilri pawl kha hloh hna;
• Chiti a luan le chuah lo zoh;
• Aa dangmi aw asiloah hninhnak kha zoh.

Zarh fatin asiloah thla fatin zohkhenhnak

Cheknak tuah ding in ruahnak cheuh mi hna cu:

• Hydraulic chiti dirhmun;
• Electric riantuan ning;
• A rawkmi thilri dirhmun;
• Mold a dikthliar;
• Hrennak a fekmi.

Zohkhenhnak phunglam ttha nih thilchuah tthatnak a tthanchoter khawh i ruahlopi in riantuan caan a zorter khawh.

7. Zumh awk tlak lungvar sernak seh sertu zeitindah kan thim lai?

Thilri tthatnak nih thilchuah tthatnak cungah direct in hnahnawhnak a pek. Hmuhtonnak a ngeimi thim lungvar sernak seh sertu hmailei ah harnak tampi hrial khawhnak ding caah a cawtu hna kha a bawmh khawh hna.

Thiamsang thilri a petu nih a tanglei hi a pek awk a si:

• A ttha ngaimi lungvar sernak seh;
• Mah duhning in sermi thilchuah khawhnak lam;
• Install tuahnak lamhruainak;
• Riantuantu cawnnak;
• Spare parts bawmhnak;
• Zuar hnu thiamnak lei riantuannak.

Bochan tlak thilchuaktu nih thilri a zuar lawng si loin caan saupi a fekmi thilchuah khawhnak ding caah a cawtu hna zong a bawmh hna.

 

Biadonghnak: A dikmi buainak tawlrelnak thawngin chuah khawhnak tthatnak kha tthanchoter

Hngalhthiamnak lungvar sernak seh buainak tawlrelnak lam lungvar sernak sehzung riantuantu paohpaoh caah a biapi. Pressure tlawm, lungvar ttha lo, seh a dir, le hydraulic rawhnak tibantuk buaibainak hna cu a dikmi zohfelnak le zohkhenhnak in rang tein tawlrel khawh a si tawn.

A zungzal in zohkhenhnak, ttha tein riantuannak, le thiamsang thiamnak bawmhnak nih thilri riantuan caan a zorter khawh i thilchuah tthatnak a tthanchoter khawh.

Lungvar sernak sehzung hmete na hman zongah, lungvar sernak sehzung nganpi na hman zongah, thilri dik thim le ttha tein zohkhenhnak nih a fekmi, ttha tein le caan sau chuah khawhnak a bawmh lai.